The Fordson Tractor Pages Forum

Hi guys, when I put a hydraulic gauge on my aux output I’m reading around 500 PSI. Is that telling me my pump is bad. If not how can I test just the pump. Thanks for any help.

Hey guys, I went to do some mower with my rotary cutter and my lift didn't have enough power to lift the cutter. It will lift a lighter implement. i put a hydraulic gauge on the aux port and pulled the asc knob and it reading 600 PSI. I think it should be around 2000 PSI. It did raise a few time but...

Thanks

Thanks for the replies. I noticed on one of the picture that there is a top bracket on the radiator. My tractor was in pieces when I got it and doesn't have brackets on top. I bet if I put some on it it wouldn't hit.

Hey guys. My fan shroud is so badly warped that it hits the blades on and off the whole time it's running. I'm not having a easy time trying to find one. Do I really need it on there? Thanks

Thanks. The manifold heater does leak a little. I guess leaking a little for a couple months and being at that angle due to a flat could be the issue. At lease I hope that's all it is.

i check the oil and it was very high, so i decided to check the water in the radiator and it was fine. I decided to drain some of the oil and it came out like water. I'm guessing it is diesel. i tried to smell it but it just smelled like burnt oil to me. It has been seating on a flat on the left sid...

Hey guys. I rebuild my super dexta engine last summer because it was blowing oil out of the oil stick and vent tube. I ran it for a couple month fine. It's been sitting for a few month and I decided to go for a ride and I noticed that I didn't have oil pressure and oil is coming out on the dip stick...

Hey guys. I was trying to lift one side of a log with my super dexta to load on a trailor. And the tractor acted like it was not even trying to lift. My neighbor has a smaller ford tractor and it wouldn't pick it up either but his front end would come off the ground. Does the dexta have enough lift ...

Hey guys, I'm now trying to get my draft control set correct. I can not get them to set like wiki says. I don't know if it's me or the parts are to worn. I guess my first question is the main control spring the large spring on back that has the yoke attached to it? I set my lift lever 1/2 from the t...

Does anybody know where to buy a 4 blade fan for a super dexta?

That was it. Thanks

Thanks

I just found in a book where it says it should pull out after you remove the bolts. But mine is only coming out about a 1/4"

Hey, I'm trying to remove my hydraulic pump so I can replace my gasket. I have had it removed before while working on my lift. I had the lift removed that time but I was wondering if I can remove it without taking the top off. I haven't got a clear answer yet from some of the post I have read. From ...

Well my gasket on my hydraulic pump busted and shot oil everywhere so I have already drained my oil and am waiting on a replacement gasket,so I don't have to worry about oil leaking out. Thanks

Hey guys, I've finally got my rescue project rebuilt and looking new. But I'm still finding small issue. Now I'm finding that when I'm running a bush hog and hit a ant bed or very thick grass my pto will disengage. I have a small amount of forward and back play in my pto shaft. Any ideas on the prob...

My lever is parrell to the top plate(position). It's bounces with all my implements and the arms leak down soon after the tractor is cut off. My draft control only works if I pull the handle all the way back with my hand and hold it there. I'm sure it's a setup problem but I couldn't get the correct...

USA Mississippi. That would be a really long trip for me.

I saw some control valves on a web site and you have the options of blue,green and orange. What does this mean and how do I know which one I need.

So do I just replace the valves? Are they hard to find? I looked on Agriline and didn't see them. Thanks

Hi,the lift on my super dexta has some kind of internal oil leak. It bounces when i lift something. i read some of the threads on other post and lifted my lift and pulled out the auxiliary control knob and it stays up. When the control knob is in it leaks down. According to the post i saw it is eith...

I have not tried that but I will. Thanks

Hi, I'm trying to replace my seals in my rear axle. I have pulled the axle and remove the locking nut at the hub. To remove the locking nut I had to break off the top ring of the nut that has the nylon or rubber ring in it. The replacement nuts that I've seen do not have this on top of the nut. Do I...

Ok so I rebuild my first engine and everything is working good so far. I put a temporary oil pressure gauge on it to see what the pressure is and my friends said he would leave the gauge on it. My oil light works and I like the original look. My question is, is the light enough or would the gauge to...