Hello
I remember reading a thread on a DIY sandpaper/el-drill sleeve honing and cant seem to find it again.Anybody know where its at
Lost thread about cylinder de-glazing w sandpaper
-
- Site Governance Team
- Posts: 1239
- Joined: Wed Jan 29, 2014 2:41 am
- Location: Norfolk Broads UK
Re: Lost thread about cylinder de-glazing w sandpaper
Don't recall seeing that thread but I'd be very wary putting sand or emery paper down a bore regardless of how it is supported and driven, well bonded wet and dry paper perhaps but those 2 & 3 legged honing stone jobs are safer, even so I always oil above the rings and grease above that to block entry then remove the fine abrasive which inevitably ends up down there. My 2 cents on the matter others may have different methods or views and it isn't exactly a high performance Porsche engine I suppose.
Best regards
Rick - Bogside on Bure
1958 Diesel E1A Mk2 s/n 1470165 - still in working clothes
Rick - Bogside on Bure
1958 Diesel E1A Mk2 s/n 1470165 - still in working clothes
Re: Lost thread about cylinder de-glazing w sandpaper
He did it with the head and sump off + pistons out!
-and it wasent "his" thread he was responding on it.
-and it wasent "his" thread he was responding on it.
-
- Site Governance Team
- Posts: 1239
- Joined: Wed Jan 29, 2014 2:41 am
- Location: Norfolk Broads UK
Re: Lost thread about cylinder de-glazing w sandpaper
OK Svend, sorry, still don't remember the thread but a lot of people de glaze with pistons still in situ, so easy to seize the engine on first start up if the waste gets down past the piston crown
Best regards
Rick - Bogside on Bure
1958 Diesel E1A Mk2 s/n 1470165 - still in working clothes
Rick - Bogside on Bure
1958 Diesel E1A Mk2 s/n 1470165 - still in working clothes
Re: Lost thread about cylinder de-glazing w sandpaper
Good advice Rick
Re: Lost thread about cylinder de-glazing w sandpaper
Try April; 26th. under subject 'Engine Overhaul', page 3
Pavel
Pavel
-
- Site Governance Team & Expert Team
- Posts: 1092
- Joined: Thu Apr 17, 2008 3:48 am
- Location: Montague Calif. USA
Re: Lost thread about cylinder de-glazing w sandpaper
I know this isn't the question you're asking, but the easiest way to de-glaze the bores, is to put a big plough behind it and work it like a rented mule!
Re: Lost thread about cylinder de-glazing w sandpaper
thats it Pavel Have you tried it?
JC
About how long for how long before it stops smoking like a bush fire on starting! I hate all that bluish smoke
JC
About how long for how long before it stops smoking like a bush fire on starting! I hate all that bluish smoke
-
- Site Governance Team & Expert Team
- Posts: 1092
- Joined: Thu Apr 17, 2008 3:48 am
- Location: Montague Calif. USA
Re: Lost thread about cylinder de-glazing w sandpaper
Its hard to say exactly how long it will take. You need to get the coolant up to operating temperature and work it hard for a few hours. You have to give it hard work periodically or it will start burning oil again. It's possible that yours needs rings, or an overhaul.
Re: Lost thread about cylinder de-glazing w sandpaper
Many, many times SvendH, since the late 1950s from a Ford 8 to a number of Alfa Romeos that I've owned. In my earlier days I could not afford spending good money on tools that were needed only once every couple of years. And yes; it works. It's on a par with buying a rarely used clutch alignment tool when improvising with a tool set socket and insulating tape does the job just as well.
Pavel
Pavel