Search found 35 matches
- Tue May 03, 2022 12:55 pm
- Forum: Fordson Dexta
- Topic: Diesel Fuel Filter Upgrade
- Replies: 1
- Views: 5567
Diesel Fuel Filter Upgrade
Has anyone successfully replaced the old diesel fuel filter on Dexta with a spin-on filter or inline filter? Mine has proven difficult to seal and the seal that comes with the filter element does not fit.
- Sun May 01, 2022 12:55 pm
- Forum: Fordson Dexta
- Topic: 1960 diesel fuel filter washers
- Replies: 2
- Views: 4782
Re: 1960 diesel fuel filter washers
Thanks, you're right. Now I have to find that darn spring.
Marlin
Marlin
- Thu Apr 28, 2022 9:20 pm
- Forum: Fordson Dexta
- Topic: 1960 diesel fuel filter washers
- Replies: 2
- Views: 4782
1960 diesel fuel filter washers
I'm replacing the diesel fuel filter and didn't notice the location of washers when the filter came out. There is a flat metal washer 1.25" in diameter with a hole large enough to go over the center post in the filter housing and a smaller fiber washer with the same diameter center hole. Do these go...
- Tue Mar 22, 2022 11:15 am
- Forum: Fordson New Major
- Topic: Super Major rear wheel adjustment
- Replies: 10
- Views: 2496
- Mon Mar 21, 2022 1:32 am
- Forum: Fordson New Major
- Topic: Super Major rear wheel adjustment
- Replies: 10
- Views: 2496
Re: Super Major rear wheel adjustment
Tractor has solid (non-adjustable unlike those in diaggram) steel wheels (orange so I think they're stock wheels) and 16x36 tires.
- Sun Mar 20, 2022 1:04 pm
- Forum: Fordson New Major
- Topic: Super Major rear wheel adjustment
- Replies: 10
- Views: 2496
Super Major rear wheel adjustment
The outside measurement of the rear tires on my Super Major is 79". The distance between rails on my trailer is 78". Are the rear wheels able to be adjusted in width? Reversing the wheels does not seem to be an option and they do not slide on an axle like my Farmall. Thanks for the help.
Marlin
Marlin
- Sat Nov 20, 2021 12:10 pm
- Forum: Fordson New Major
- Topic: FSMD engine heater
- Replies: 7
- Views: 2724
Re: FSMD engine heater
Overnight temp was 21 degrees F and the FSMD started without any electric heaters or ether. Just pushed in the cold start button on the pump. Cranked for about 30 seconds, then started. I'm continually impressed with this engine.
Marlin
Marlin
- Mon Oct 25, 2021 11:12 am
- Forum: Fordson New Major
- Topic: Replacing exhaust manifold
- Replies: 34
- Views: 7451
Re: Replacing exhaust manifold
I've had not problems ordering from UK. DHL delivers within 5 days, but is costly ($50/shipment).
- Mon Oct 25, 2021 11:08 am
- Forum: Fordson New Major
- Topic: FSMD engine heater
- Replies: 7
- Views: 2724
Re: FSMD engine heater
I don't have a shed, but I have considered using a blanket. I could add a heat lamp if needed. I'll make sure to get some winter diesel additive in it. I have a dipstick heater that I use in the transmission of my Farmall during cold snaps. I use 50/50 coolant, so freezing there shouldn't be an issue.
- Thu Oct 21, 2021 3:51 pm
- Forum: Fordson New Major
- Topic: FSMD engine heater
- Replies: 7
- Views: 2724
FSMD engine heater
I'd like to use the FSMD to move snow this winter. Here in Iowa temps can get to -10 degrees F. I have installed a freeze plug heater in the Dexta, but don't see any accessible freeze plugs on the SM. The temp sender on the upper block is a non-standard pipe thread, so I haven't had any luck install...
- Tue Oct 19, 2021 3:25 pm
- Forum: Fordson New Major
- Topic: FSMD change + gound to - ground
- Replies: 1
- Views: 1554
FSMD change + gound to - ground
1962 FSMD with original generator & voltage regulator. All of my other tractors are negative ground. Can I just change this from + ground to - ground without changing anything else in the generator/regulator system? Thanks.
Marlin
Marlin
- Wed Oct 06, 2021 10:41 am
- Forum: Fordson New Major
- Topic: FSM gear box double lipped seal installation
- Replies: 38
- Views: 9042
Re: FSM gear box double lipped seal installation
Is there an easier way to remove the circlip from the shaft, than to lever it off with a screwdriver? Thanks
Marlin
Marlin
- Fri Oct 01, 2021 8:15 pm
- Forum: Fordson New Major
- Topic: FSM gear box double lipped seal installation
- Replies: 38
- Views: 9042
Re: FSM gear box double lipped seal installation
Can the seals be extracted from the PTO gearbox & replaced without dismantling the gears, bearings & shafts? Thanks.
Marlin
Marlin
- Thu Sep 30, 2021 6:36 pm
- Forum: Fordson New Major
- Topic: FSM gear box double lipped seal installation
- Replies: 38
- Views: 9042
Re: FSM gear box double lipped seal installation
In the diagram that I have, the PTO seals look like they are nested, one inside the other & the parts manual lists the number (E1ADKN-7297-B) as a pair. Is this correct, or do I need to order 2 seals & place them back-to-back?
- Thu Sep 30, 2021 4:37 pm
- Forum: Fordson New Major
- Topic: FSM gear box double lipped seal installation
- Replies: 38
- Views: 9042
Re: FSM gear box double lipped seal installation
Thanks for all the help. This discussion helped me understand the seal differences & diagnosis. Since the rear end oil is so low that I can see the lower main shaft through the transmission filler, I'm assuming the pto seal is the culprit, and that I can change that without splitting the tractor. Fr...
- Wed Sep 29, 2021 8:30 pm
- Forum: Fordson New Major
- Topic: FSM gear box double lipped seal installation
- Replies: 38
- Views: 9042
FSM gear box double lipped seal installation
I understand that a special tool is required to successfully install the double lipped seal between the gear box & rear end to stop the rapid draining of lubricant from gear box to rear end. In the USA, is this tool usually available at Ford (New Holland) dealers? Thanks.
Marlin
Marlin
- Thu Sep 23, 2021 2:37 pm
- Forum: Fordson New Major
- Topic: FSM dual clutch
- Replies: 32
- Views: 9293
- Thu Sep 23, 2021 2:32 pm
- Forum: Fordson New Major
- Topic: FSM dual clutch
- Replies: 32
- Views: 9293
Re: FSM dual clutch
Woops. I don't know what I did wrong that the image didn't appear. I thought I formatted it as I did before. Is there a limit to how many I can post?
- Thu Sep 23, 2021 2:31 pm
- Forum: Fordson New Major
- Topic: FSM dual clutch
- Replies: 32
- Views: 9293
Re: FSM dual clutch
Completed FSM dual clutch disk replacement successfully. Thanks for all your help. This is the disk hub alignment tool I made. I also used the headless bolts to re-install flywheel & clutch assembly by myself. Long bolts used to align engine & bell housing for re-assembly. https://i.postimg.cc/pdxWZ...
- Tue Sep 21, 2021 11:37 pm
- Forum: Fordson New Major
- Topic: FSM dual clutch
- Replies: 32
- Views: 9293
Re: FSM dual clutch
Will do. Thanks!
Marlin
Marlin
- Tue Sep 21, 2021 12:43 pm
- Forum: Fordson New Major
- Topic: FSM dual clutch
- Replies: 32
- Views: 9293
- Mon Sep 20, 2021 2:33 pm
- Forum: Fordson New Major
- Topic: FSM dual clutch
- Replies: 32
- Views: 9293
Re: FSM dual clutch
By the way, I'm reading the " (double quote sign) as inches since I'm in the USA. If this is incorrect, please let me know.
- Mon Sep 20, 2021 2:30 pm
- Forum: Fordson New Major
- Topic: FSM dual clutch
- Replies: 32
- Views: 9293
Re: FSM dual clutch
I made spacers according to the diagram (0.575" & 0.597") and have compressed the release levers of the transmission & PTO pressure plates but still cannot obtain the clearance required to insert the spacers. The PTO levers are completely down to the clutch cover and the clearance is not nearly 0.59...
- Thu Sep 09, 2021 9:49 pm
- Forum: Fordson New Major
- Topic: FSM dual clutch
- Replies: 32
- Views: 9293
Re: FSM dual clutch
The flywheel has the bronze pilot bushing. Should I replace this with a new ball bearing pilot bearing or leave the bronze one where it is? Thanks.
Marlin
Marlin
- Fri Sep 03, 2021 6:37 pm
- Forum: Fordson New Major
- Topic: FSM dual clutch
- Replies: 32
- Views: 9293
Re: FSM dual clutch
After cleaning up the clutch surfaces, I see some fine cracks (like fish scales) in the transmission clutch pressure plate surface. Do these need to be machined out? If so, is this something a general automotive machine shop can do?
Marlin
Marlin