The Fordson Tractor Pages Forum

There was no pin according to where the manual showed it placed. I adjusted the pedal according to the manual, and even tried adjusting it a tad bit to tight, so it only had about 1/2 inch of slack in the pedal, and when I press the clutch pedal all the way down the pto still turns my finish mower w...

I am not sure about the pin yall have mentioned, nor have I ever paid attention to there being a hole around the clutch area.
I pray it's that easy.
I have not had a chance to work on it yet, but am going to read through the link for adjustment according to the manual now.

I am not sure about the pin yall have mentioned, nor have I ever paid attention to there being a hole around the clutch area.
I pray it's that easy.
I have not had a chance to work on it yet, but am going to read through the link for adjustment according to the manual now.

Thank you for all the replies. I have adjusted the pedal to have about 1.5 inches of free play, but will look at the manual and see if I am doing it correctly. The problem has been there every since I bought the tractor, but I've learned how to engage the pto while cranking the engine 😅. I can disen...

Are there any adjustments to the pto part of the dual clutch setup on a Fordson super major, other than the pedal adjustments ? My clutch pedal will stop forward movement, but will not stop my pto from turning, even while turning a rotary cutter in heavy brush. I have even tried to have the cutter r...

Thank you for the replies.
I appreciate them all.

Ha ha. I wil try to stop the cruelty to my major, but it likes some dirty, hard work from time to time.. lol
Thank you for your advice !
At 1200 rpm heavy brush will bog my engine as well.
I will bump the rpm up a little, so it won't strain as much.
Thanks again !

I have a 1962 fordson super major. I have always used 1200 engine rpm when running any kind of pto driven attachment that is rated for 540 rpm. I read a conflicting article that on the super major that said if the "raised pto" was a option, which my original tachometer did say on it, then the engine...

Are you saying I should put locktite on the plug that has to be pulled out, to be able to get the unload valve out ? That thing was a beast to get pulled out, and i had to tap it back in, very lightly with a small chissel hammer. It seemed tight, but I will for sure try the locktite on the plug. Any...

With the 2000 pound brush mower, it will drop about 4 inches in maybe 10 seconds.
Basically from a high cutting heighth, back to the ground, in 10 seconds or less.
The blades edges are about 3 inches high, inside the deck, so I carry it about 3-4 inches high, and then re cut it lower.

Have you replaced the solenoid ?
I thought my starter was bad and it turned out to be the solenoid wouldn't pass the amperage needed.

I just went through this myself. No fuel out of the tank, to the pump basically. The petcock on the tank was clogged. It was a mess, trying to get the petcock out, with about 5 gallons of fuel in the tank. I should have siphoned the tank ! After I removed the petcock, I screwed it back in, just to u...

I had a under slung exhaust with a silencer type muffler. I removed the muffler, because it was full of crud. The plus side of a under slung exhaust is not having to worry about ripping it off on low hanging tree branches. The draw brack is the exhaust when you are changing implements. Rarely are th...

I have a 62 super major. The lift top has a block off plate on top of the lift top, where alot of others seem to have things like flow control, tipping pipe, etc. Mine doesn't have any of that. It is only the lift top, with the check valve in the front, and the pressure relief valve. Other than that...

Thank you all for replying about the starter fitment. My tractor usually fires up, after 3 to 4 good revolutions, with a strong battery and starter. Luckily I tested my battery voltage and noticed my battery was charging at almost 17 volts, at a raised rpm. ! I had the battery tested and it tested b...

I honestly don't know anything about the starter fitment. Maybe someone that has already converted their major to the newer starter can comment on that.

Thank you both very much for your replies.
I am going to go ahead and switch to the solenoid type, Ford 4000 starter as well, since it worked for you both.

I have a 1962 super major. I am looking for a injector rebuild kit, and found a injector tip replacement online. The replacement tip advertisement, says it is suitable for a Fordson super major as well as a older Ford thousand series, like a Ford 4000. Does this sound correct ? They both use the sam...

I just wanted to post back and say thank you. The 7/16 ball size was a perfect match, to the old ball in my check valve.

Thank you very much for that information !

I have a super major that the check valve, or some call it the non return valve, the ball is dented slightly. I want to get 2 new ones and use one to lightly tap the ball against the seat, to hopefully form a better fit. Then use the brand new one for use. What size ball am I supposed to use ? http:...

That is exactly the guidance I was looking for.
Now the hard part seems to be, to find a ball that exact size !
Thank you for the advice !

What do you mean by sealing plugs ? I do not understand what part that is, by the name. I am pretty confident that all my orings are good, as the tractor was doing this bobbing thing, before all new orings and work metioned above. The problem that led me to rebuild the entire lift top, and have the ...

I have had zero luck. I have been able to find orings but was looking for somewhere in the U.S that would build me a new pump, or could sell me a good used one. I tried buying one from a individual and it was a bigger piece of garbage than the one that I already had. I wish I knewof somewhere that w...

I have a 62 super major, but I swear it looks like a power major hydraulic top. I am not sure if thats possible, but I dont have all the tipping valves, or remote valve, or any of that. Just a blank plate, blocking that area off. I have the old style pressure relief valve in the front, behind the bi...