The Fordson Tractor Pages Forum

From Finland I can't find any dealer where to buy new lever screws. Do anyone have ideas where to order those screws in europe?

BR
Ilkka

Result can be seen there: https://aijaa.com/KKlnuO and https://aijaa.com/YHS87i. So it did not last even two hours test run. Bearing was totally damaged and adjusting nuts were almost totally worn out. Wery sad thing for me to hit my head for every place...

Br Ilkka

We compare thw old and new bearings with local dealer. Looks like old one have some kind of "projection" and new is just flatten. Difference 6,5 mm came from this "projection". Dealer said that old style of bearing is not available and they recommended to adjust this missing 6,5 mm by the rod. Also ...

What might be the correct part number for the dual clutch bearing? I think here in Finland it is not available. Persons in local forum says that it is possible to adjust it by rod and, but?

BR Ilkka

Billy26F5 wrote: ↑

Mon Jul 19, 2021 4:30 pm

Unfortunately no, you'll need the correct bearing.
Sandy

But for what reason I need correct lenght of bearing? If I just compensate the difference ~ 8 mm by extending the thread of rod.

BR Ilkka

Looks like I have bought wrong size of release bearing. The original bearing was 28,45 mm lenght and the new one is 22 mm. Is this kind of difference possible to adjust by rod?

BR Ilkka

Hello all!

I have Super Dexta with double clutch. Yesterday I measured the lenght of rod and it is ~78,5 cm. I did clutch overhaul and looks like need to shorten rod length, or maybe make longer thread to adjust clutch.

BR: Ilkka

Manual says that ensure the p.t.o and transmission levers adjusting screws project out of the levers approximately the same distance (3/8 inch, 9,53 mm). Is this meaning that 3/8 inch distance between pto and ttansmission levers adjusting screws distance or something else. I do not have so fluent en...

Finally, today whole clutch package is ready for installation to the flywheel. Pilot bearing, clutch release bearing, pto clutch disc and trans clutch disc has been renewed. One question more, how to adjust the double clutch release levers without any special setting pad?

BR
Ilkka

Thanks again! How to make adjustments without any special adapter tools when discs are changed?

BR
Ilkka

Today tried to start opening clutch. But looks like clutch pressure plate springs are very tight. How to take out clutch pressure plate spring retainers without any special tools?

BR
Ilkka

Today morning I found the reason why engine is rotating ok when it's separately from the tractor. Clutch pto disc is damaged do to my too heavy force to assembly engine to the tractor. You can find picture there (https://ibb.co/GVbbGMM). What do you think is it better to deliver clutch to the specia...

Today I removed all sprayers and tried to rotate engine. Engine was rotating very good by hand and by battery wtih 35mm2 cables. But when I connected engine back to the tractor, engine came sticky and more sticky. And when I tightenes all bolts betwee engine and clutch block, it was so tight that I ...

Ok, Bulletin Board. :D Today I tried to rotate engine with cables directly to the starter. Again engine rotating slowly and very tight and my cables are not big enough to do this. Oil pressure gauge shows 10 - 15 psi when engine is rotating slowly by starter. Again by hand engine is rotating like ea...

Today I put starter back to the engine and I opened oil switch and put some paper for the opening. The I rotate engine directly from starter with cables. First and second start was very tight, but third start was succesful and engine was rotating more and more smoothly and engine started up and runn...

Iikka I have messaged you here on the BB. Jerry Hello Jerry! Yes we have sent some mails at the beginning of 2020 regarding my oil leak problems. 😁 I remember, but what do you mean BB? Today starter has been checked by auto electric expert and he told me that starter is fine. I've got also pressure...

Today it was fourth time to split Dexta and remove clutch and flywheel. Starter motor was running ok without load. When I removed flywheel I found some small axial movement on crankshaft. Should there be some minor movement or not? I think now it is better to find some Dexta specialist to check what...

Today tried to start engine again. Still hard to rotate engine by own battery. Same thing again and I don't connect any extra battery to rotate engine anymore. After when I change oil pan gasget set this problem came. Do not know what to do? :roll: Maybe I should deliver engine to some workshop who ...

Thanks for the picture! Is that connection size 1/4" NTP? Hard to find from finland any inch size things. Looks like mainly small particles are cork in the sump. Atleast with gas torch almost all was burned away. When I opened again oil pan, I found loosen connection for oil suction pipe to the oil ...

Try turning by hand by all means, but if it's at all stiff you won't be able to run (you'll have a better idea if you remove the injectors so you don't work against compression). The seals do need soaking, but you won't be able to run if there were bronze filings in the sump until you find where th...

Try turning by hand by all means, but if it's at all stiff you won't be able to run (you'll have a better idea if you remove the injectors so you don't work against compression). The seals do need soaking, but you won't be able to run if there were bronze filings in the sump until you find where th...

One more thing. I didn't soak the rope seals with oil. Could it be a reason for this problem?

Would it be possible try to turn engine by hand to check if it's totally stuck? Or is there some risk for that?

BR
Ilkka

Unfortunately oil pressure light bulb was broken. I opened just oil pan strainer, screen was bended like oil suction pipe was maybe hitted when I was installing oil pan and motor together. I think screen was blockin oil to the oil suction pipe. Also there was small particles bronze... :| Looks like ...

Fuel supply was ok. How I can easily check the oil pressure? Engine sounds like it was going stuck before it stopped. When I earlier remove oil pan I saw that strainer was bended, looks like the oil suction pipe was not earlier in correct position. Now I have plan to remove oil strainer and check if...