Search found 1926 matches
- Wed Apr 24, 2024 11:51 pm
- Forum: Fordson New Major
- Topic: FSMajor wheel wobble
- Replies: 7
- Views: 35
Re: FSMajor wheel wobble
You'll want to use a feeler gauge between the extension and spindle arm. There should be no play in the wheels, so that's what I would check first. The grooves are indeed at 2" in the tie rod ends, but in some cases you have some tolerance to play with in those as well as the tie rod tube, Super Bil...
- Wed Apr 24, 2024 9:43 pm
- Forum: Fordson New Major
- Topic: FSMajor wheel wobble
- Replies: 7
- Views: 35
Re: FSMajor wheel wobble
I would start by checking your play, make sure the wheel bearings are set up properly and that the spindle arms are at 0.025" from the extension (assuming you have rubber seals in there, felt seals used before the Super Major need 0.002") and are in the correct position. Not all tie rods are accurat...
- Tue Apr 23, 2024 8:49 am
- Forum: Fordson New Major
- Topic: My New Performance Super Major Story.
- Replies: 27
- Views: 7014
Re: My New Performance Super Major Story.
Burst hoses are always irritating, but often it does work out better to replace doubtful hoses sooner rarther than later. I think all Super Major's have the same hydraulic pump, which is different from earlier pumps. What is different is the gear ratio, as the NP PTO is slower the PTO to pump gear r...
- Tue Apr 23, 2024 8:36 am
- Forum: Fordson New Major
- Topic: Fordson and Dexta clutch pilot bearing causing shaft damage
- Replies: 20
- Views: 1169
Re: Fordson and Dexta clutch pilot bearing causing shaft damage
Hope everything goes well.
Sandy
Sandy
- Tue Apr 23, 2024 8:34 am
- Forum: Fordson New Major
- Topic: Hi-Lo Lever
- Replies: 3
- Views: 93
Re: Hi-Lo Lever
I don't know why they changed the knob in 54, they must have thought the one piece casting would be cheaper. Anything post Power Major however must have a separate knob as otherwise the lever won't fit through the dash.
Sandy
Sandy
- Tue Apr 16, 2024 8:50 am
- Forum: Fordson New Major
- Topic: Hi-Lo Lever
- Replies: 3
- Views: 93
Re: Hi-Lo Lever
The early levers had a large separate knob and were fixed on with a pin. these had a bad habit of getting very loose, so were replaced with the clamp type in around 54, this was the one piece type, which was replaced by a two piece clamp type with the Power Major with a smaller knob. Ebro never used...
- Sun Apr 14, 2024 10:22 pm
- Forum: Fordson New Major
- Topic: Super Major low hydraulic pressure
- Replies: 26
- Views: 1289
Re: Super Major low hydraulic pressure
I suggest tightening up the LH brake for now, here's the brake manual: https://www.fordson.se/6_Framaxel_styrning_bromsar_d%E4ck_Verkstadsmanual_167-190.pdf Know all about brakes misbehaving and it's not fun, the drum brakes are rather better in that sense, as the disk brakes can very easily get int...
- Sun Apr 14, 2024 10:37 am
- Forum: Fordson New Major
- Topic: Super Major low hydraulic pressure
- Replies: 26
- Views: 1289
Re: Super Major low hydraulic pressure
Glad to see you've got that working and very impressed with your skills on the support bracket. I think it would be nice to have some pics of the brakes so that the very unusual mixture of parts in use is clear. I don't know if you've seen the recent Super Billy news but I'll post pics so you have a...
- Wed Apr 10, 2024 10:23 pm
- Forum: Fordson Dexta
- Topic: Super Dexta Hydraulic Adjustment - help please
- Replies: 9
- Views: 323
Re: Super Dexta Hydraulic Adjustment - help please
Glad you fixed that.
Sandy
Sandy
- Wed Apr 10, 2024 3:16 pm
- Forum: Fordson New Major
- Topic: NP ratio stamping
- Replies: 7
- Views: 4414
Re: NP ratio stamping
I haven't got any further on this but I can confirm Super Billy is a slow ratio, as he's a lot slower than Billy. The PTO is not however the same as Ford specified. 540 rpm is at 1599 rpm rather than 1473 rpm, meaning that Ebro had other chenges in there (the PTO gear has 33 teeth instead of 32 and ...
- Wed Apr 10, 2024 3:00 pm
- Forum: Fordson New Major
- Topic: PTO problem? Gearbox noise Super major 1963
- Replies: 10
- Views: 298
Re: PTO problem? Gearbox noise Super major 1963
Unfortunately it's not as simple as that, E1ADKN-7255 was used till 08C-960337, when it was replaced by E1ADDN-7255, with the previous part no longer available. The new shaft and seal will fit in older castings, but it's not recommended to use the older shaft and seals in the NP box as the new desig...
- Mon Apr 08, 2024 9:09 pm
- Forum: Fordson New Major
- Topic: Fordson and Dexta clutch pilot bearing causing shaft damage
- Replies: 20
- Views: 1169
Re: Fordson and Dexta clutch pilot bearing causing shaft damage
This points to the metric bearing even more. Try it and see how it feels.
Sandy
Sandy
- Fri Apr 05, 2024 7:11 pm
- Forum: Fordson Dexta
- Topic: Super Dexta Hydraulic Adjustment - help please
- Replies: 9
- Views: 323
Re: Super Dexta Hydraulic Adjustment - help please
Normally only one but some do have two.
Sandy
Sandy
- Fri Apr 05, 2024 1:20 pm
- Forum: Fordson New Major
- Topic: Big news!
- Replies: 1
- Views: 94
Big news!
After a long silence on the subject there's a big development: Super Billy is back! https://i.postimg.cc/13gMHNLM/2024-D4-28.jpg https://i.postimg.cc/yY1bFx1r/2024-D4-26.jpg https://i.postimg.cc/4d11dv94/2024-D4-33.jpg https://i.postimg.cc/1X5rNgGG/2024-D4-34.jpg https://i.postimg.cc/rmTJMZzY/2024-D...
- Fri Apr 05, 2024 12:06 pm
- Forum: Fordson New Major
- Topic: Fordson and Dexta clutch pilot bearing causing shaft damage
- Replies: 20
- Views: 1169
Re: Fordson and Dexta clutch pilot bearing causing shaft damage
I would see if you can get a shrouded bearing, they're much better for this job. Probably is worth measuring the flywheel, but it all points to the metric mearing at the moment.
Sandy
Sandy
- Fri Apr 05, 2024 12:02 pm
- Forum: Fordson New Major
- Topic: winter project
- Replies: 7
- Views: 542
Re: winter project
Good work, looks like you were unlucky, Super Billy's bush from Agriline was good. Your spindle bushes are better than what we got, better to have too many grooves than none. The new seals are always big and need lots of early attention. Good to see you got that screen, I can't think how many will s...
- Fri Apr 05, 2024 11:48 am
- Forum: Fordson Dexta
- Topic: How soon after an engine rebuild does one need to retorque.
- Replies: 11
- Views: 570
Re: How soon after an engine rebuild does one need to retorque.
I think you have been very lucky! Probably worth doing anyway though.
Sandy
Sandy
- Thu Apr 04, 2024 9:19 am
- Forum: Fordson Dexta
- Topic: Super Dexta Hydraulic Adjustment - help please
- Replies: 9
- Views: 323
Re: Super Dexta Hydraulic Adjustment - help please
The manual says the position control spring has 10.7 coils and is 1.96" long under 72 lbs and 1.52" under 152 lbs. I think your new spring will still not work but see if it improves anything or not.
Sandy
Sandy
- Thu Apr 04, 2024 9:05 am
- Forum: Fordson New Major
- Topic: Fordson and Dexta clutch pilot bearing causing shaft damage
- Replies: 20
- Views: 1169
Re: Fordson and Dexta clutch pilot bearing causing shaft damage
I've had a look around and the closest I can find is a 1/2" thick bearing. I'm still a bit unsure about this, I wouldn't expect a 1950's part list to have the sort of mistakes we get now, but the only way to be sure is to measure several flywheels, input shafts and original pilot bearings to see wha...
- Tue Apr 02, 2024 10:09 pm
- Forum: Ford and Fordson Conversions
- Topic: Super Major temp gauge
- Replies: 2
- Views: 150
Re: Super Major temp gauge
I suggest you see this, you might be able to do it yourself: viewtopic.php?p=61012#p61012
Thanks for letting us know that Speedograph don't do them anymore, although the Fordson ones are AC, whereas Spedograph are mainly Smiths.
Sandy
Thanks for letting us know that Speedograph don't do them anymore, although the Fordson ones are AC, whereas Spedograph are mainly Smiths.
Sandy
- Tue Apr 02, 2024 12:27 pm
- Forum: Fordson New Major
- Topic: PTO problem? Gearbox noise Super major 1963
- Replies: 10
- Views: 298
Re: PTO problem? Gearbox noise Super major 1963
Sounds like Mathias is right, you'll need to drain both the gearbox and rear axle for this, also be careful as everything is heavy. New seals are available, the bearings are part nos. BB-7025 and BB-7065, they should have a number stamped on them telling you what kind they actually are. The o-ring m...
- Tue Apr 02, 2024 12:16 pm
- Forum: Fordson New Major
- Topic: Fordson and Dexta clutch pilot bearing causing shaft damage
- Replies: 20
- Views: 1169
Re: Fordson and Dexta clutch pilot bearing causing shaft damage
See how it fits, if it feels very tight swap it for a higher clearance bearing, you've got a sealed bearing, which is an unusual choice for a pilot bearing, they're normally of the shrouded type. Good bearings are always worth using.
Sandy
Sandy
- Mon Apr 01, 2024 3:32 pm
- Forum: Fordson New Major
- Topic: Fordson and Dexta clutch pilot bearing causing shaft damage
- Replies: 20
- Views: 1169
Re: Fordson and Dexta clutch pilot bearing causing shaft damage
The Z is not a clearance, it means the bearing has a metal shroud covering the balls. I have often also seen CN being between C2 and C3, but that might not be a real clearance. There is a chance that the metric confusion could have occurred, but the 1950's SKF list for Fordson tractors would likely ...
- Sun Mar 31, 2024 5:15 pm
- Forum: Fordson New Major
- Topic: Fordson and Dexta clutch pilot bearing causing shaft damage
- Replies: 20
- Views: 1169
Re: Fordson and Dexta clutch pilot bearing causing shaft damage
It shouldn't be too tight a fit, as the input shaft has to slide in and out when the engine is fitted or removed. According to what Mike says you want the bearing to be a bit free, as opposed to having a preload. I had always understood C4 to have a slight preload while C2 has a bit of play (as an e...
- Thu Mar 28, 2024 10:09 pm
- Forum: Fordson Dexta
- Topic: Super Dexta Hydraulic Adjustment - help please
- Replies: 9
- Views: 323
Re: Super Dexta Hydraulic Adjustment - help please
Not totally sure what's wrong yet but here's the manual. http://www.smallholderservices.co.uk/si ... hydraulics
I'll get back to you soon if I can think of something, check to see if you find anything else worn in there.
Sandy
I'll get back to you soon if I can think of something, check to see if you find anything else worn in there.
Sandy