Search found 170 matches
- Mon Aug 11, 2014 7:47 am
- Forum: Fordson New Major
- Topic: Injection pump bearings
- Replies: 5
- Views: 6550
Injection pump bearings
Hello all, I am replacing the bearings in the injection pump from a 1955 E1A and appart from discarding two or three injection pumps due to rusted cams etc I have found another problem which others may like to know about. I took the step in advance of ordering a kit from England to do the job, howev...
- Thu Aug 07, 2014 6:27 am
- Forum: The PARTS SWAP forum!
- Topic: N model rear diff housing
- Replies: 0
- Views: 3115
N model rear diff housing
I am looking for a late N model housing that has the bulge for the starter motor, as I need to fit a starter motor to my N model grader. it needs to be in Australia and preferably West Australia.
Mike
Mike
- Sun Oct 27, 2013 4:08 pm
- Forum: Ford and Fordson Conversions
- Topic: Power major 6 cylinder conversion
- Replies: 85
- Views: 182507
Re: Power major 6 cylinder conversion
Hello Arno,
can you please tell me how you overcame the excess endfloat in the clutch shafts as mine needs to be reduced due to the common thrust face wear they suffer?
Mike
can you please tell me how you overcame the excess endfloat in the clutch shafts as mine needs to be reduced due to the common thrust face wear they suffer?
Mike
- Sun Oct 27, 2013 3:56 pm
- Forum: Ford and Fordson Conversions
- Topic: malcome moore
- Replies: 12
- Views: 24090
Re: malcome moore
Hello Brockwood, I have two Malcolm Moore Fordson conversions, the first is a grader based on a 1937 N model, I have to get this back on wheels so I can get it into a position where I can do the other work to restore it. I have a leed on the whereabouts of one other, and I found a picture on the int...
- Sun Oct 27, 2013 2:51 am
- Forum: Fordson New Major
- Topic: Camshaft Bearings Technical Information
- Replies: 5
- Views: 6174
Re: Camshaft Bearings Technical Information
Hello again Robert, The cranks in the next model ( K series Trader ) seem the same too, ( same flywheel ) would need to check first though. I think the D series will have changed cranks by that stage, I suppose you have looked at this option as there are plenty of old ones of those around, if you kn...
- Fri Oct 25, 2013 2:37 am
- Forum: Fordson New Major
- Topic: Camshaft Bearings Technical Information
- Replies: 5
- Views: 6174
Re: Camshaft Bearings Technical Information
Hello Robert, I have just had notification that my bearings have arrived, I think the price was about $I50 Australian, I will go to town and get them this morning. I would be cautious about welding a crank, unless you ment metal spraying, even this can have issues if not bonded correctly. If I were ...
- Fri Oct 25, 2013 2:01 am
- Forum: Ford and Fordson Conversions
- Topic: 6 Cyl Thames trader camshaft bearings needed urgently
- Replies: 5
- Views: 8526
Re: 6 Cyl Thames trader camshaft bearings needed urgently
Hello Jan,
to obtain your 6cyl 7C5757 camshaft bearings please contact the Poland ACL distributor
Shemek Wisniewski <shemek.wisniewski@gmail.com>
Mike
to obtain your 6cyl 7C5757 camshaft bearings please contact the Poland ACL distributor
Shemek Wisniewski <shemek.wisniewski@gmail.com>
Mike
- Thu Oct 24, 2013 3:52 am
- Forum: Ford and Fordson Conversions
- Topic: date of fordson super major and pignon / roadspeed question
- Replies: 21
- Views: 47541
Re: date of fordson super major and pignon / roadspeed ques
There are also different diamaeter bull gears too according to the parts books. 17.65 inches reduced to 17.52 inches. Seems like they needed a larger diameter pinion shafts to be able to hollow them out for the diff lock activating pin and to do this they reduced the corresponding bull gear diameter...
- Wed Oct 23, 2013 3:37 am
- Forum: Fordson New Major
- Topic: Camshaft Bearings Technical Information
- Replies: 5
- Views: 6174
Re: Camshaft Bearings Technical Information
Thank you for all those specifications, my camshaft is 3.060 as indicated as the maximum camshaft size, so all is great there, I have ordered some standard bearings for mine, though .010 undersize ones are also available for worn cams. Mike1962 model True Blue Posts: 111 Joined: Wed Feb 02, 2011 8:0...
- Wed Oct 23, 2013 3:32 am
- Forum: Ford and Fordson Conversions
- Topic: 6 Cyl Thames trader camshaft bearings needed urgently
- Replies: 5
- Views: 8526
Re: here are the bearings
hi mike now here is what i found in the www about the cam bearings for the 4 and 6 zyl. engines (589e/590e/591e/592e) The company: http://www.acl.com.au and the technical information Camshaft Bearing Set 5C5757 Oversize STD Brand ACL Manufacturer ACL Camshaft Bearing (c) 5756 - 1 Manufacturer ACL M...
- Sat Oct 19, 2013 8:28 am
- Forum: Ford and Fordson Conversions
- Topic: 6 cylinder Fordson project West Australia
- Replies: 17
- Views: 37147
Re: 6 cylinder Fordson project West Australia
Hello Hank, Did you ever get the badges you wanted, I tried to send you a message but you obviously did not recieve it? Please give me a ring and we can discuss it further? My son has been working away so progress on the grader is very slow, but as the weather clears we hope to re start on it. I hav...
- Sat Oct 19, 2013 7:44 am
- Forum: Ford and Fordson Conversions
- Topic: New to this, 6 cylinder engine confusion
- Replies: 13
- Views: 19572
Re: New to this, 6 cylinder engine confusion
Hello all, a word of warning, there are reasons that the cranks wear badly, firstly is water in the oil and also there is the fuel bleed off lines cracking the lead solder or the re using tof he copper sealing washers. The crank I am about to throw out is destroyed from trying to reuse the rear tape...
- Sat Oct 19, 2013 6:59 am
- Forum: Ford and Fordson Conversions
- Topic: Wishbone position on 6 cylinder Majors
- Replies: 2
- Views: 4372
Re: Wishbone position on 6 cylinder Majors
I know what you mean about the small pin, this seems to have been a carry over from the N model and kept, so that front axles could be interchanged, from my quick observations there is very little difference to the mounting holes sizes or their position from the N to the Power Major, but by the time...
- Sat Oct 19, 2013 6:47 am
- Forum: Ford and Fordson Conversions
- Topic: Aveling Barford grader plans or pictures required
- Replies: 0
- Views: 3778
Aveling Barford grader plans or pictures required
Hello everyone, My son wants to build a replica of an Aveling Barford grader using my old spare parts 1955 New Major as a base. I have shown him how to do the rear axle seals and hydraulic top seals, and we need to split and do the gearbox seal and we can tthen start on mounting a blade. We have fit...
- Sat Oct 19, 2013 6:33 am
- Forum: Ford and Fordson Conversions
- Topic: 6 Cyl Thames trader camshaft bearings needed urgently
- Replies: 5
- Views: 8526
Re: 6 Cyl Thames trader camshaft bearings needed urgently
Thank you very much, I have made enquiries to get these bearings. It seems to be the front bearing that fails more, probably due to vibration from the front gears, I pulled down three 590E engines and every one had erosion problems in the front bearing, this could be from the gears or or possibly fr...
- Wed Oct 02, 2013 3:32 pm
- Forum: Ford and Fordson Conversions
- Topic: 6 Cyl Thames trader camshaft bearings needed urgently
- Replies: 5
- Views: 8526
6 Cyl Thames trader camshaft bearings needed urgently
Hello all, I am having to rebuild my 6cyl engine and everything is done except for the camshaft bearings which are not a lot of use, the part numbers are; Front cam bearing E1ADKN 6261 -A one only, Remaining bearings E1ADKN 6262 -A 6 required. I hope someone can help me or I am completely stuck with...
- Thu Sep 26, 2013 6:08 am
- Forum: Fordson New Major
- Topic: Block bearing bores streached need original size
- Replies: 2
- Views: 2767
Block bearing bores streached need original size
Hello everyone, I need to find out the machining size for the main bearing tunnel as the bearing shells were moving from excessive bearing clearance and I am having them closed up and remachined.
Can anyone please tell me the size to have the bearing cap bores in the block machined to?
Mike
Can anyone please tell me the size to have the bearing cap bores in the block machined to?
Mike
- Sun May 05, 2013 5:39 pm
- Forum: Fordson New Major
- Topic: Australian compliance ID plates
- Replies: 3
- Views: 4286
Australian compliance ID plates
Hello all, I wonder if anyone can tell how to read the Ausie plates correctly as I am guessing a bit? The New Majors here had the engine number stamped into a single tag ion the top middle of the firewall just above the rocker cover. From 1957 when the mark two models came out the plates changed, th...
- Sun May 05, 2013 4:41 pm
- Forum: Ford and Fordson Conversions
- Topic: county super 6 2wheel drive
- Replies: 14
- Views: 23596
Re: county super 6 2wheel drive
Hi Liam Sounds like you have been reading the same article in the magazine that landed here in my mail box in Canada on Friday :wink: :) I wish I had one of those Countys, Or the parts where easy to get here :cry: I'd love to build a replica of it. I'm not a fan of that nose cone on the 4x4 county ...
- Wed Jun 20, 2012 3:31 am
- Forum: Ford and Fordson Conversions
- Topic: Trouble starting when hot!
- Replies: 6
- Views: 7966
Re: Trouble starting when hot!
Hello all, The battery leads and those from the statrer solanoid do develop resistance, the braided copper earth leads are a particular proplem, I have had these get very hot from resistance when starting a new engine. The solanoid also does deteriate over time as well, I recently replaced my starte...
- Wed Jun 20, 2012 3:13 am
- Forum: Ford and Fordson Conversions
- Topic: 590E engine date and Thames Trader compliance
- Replies: 7
- Views: 14220
Re: 590E engine date and Thames Trader compliance
Hello, Ollie, mine had twin filters bolted to the engine and a Bosch lift pump as well and like you I have removed all this and made it the same as the tractor. I made a blanking plate for the side of the Injection pump from 6mm plate. My project has slowed due to a protracted dispute with a neighbo...
- Thu Apr 26, 2012 2:55 am
- Forum: Fordson New Major
- Topic: 19" cast wheels, what difference between three and four hole
- Replies: 7
- Views: 8004
Re: 19" cast wheels, what difference between three and four
Hello again, for your information, In West Australia Agricultural N models had the 19" wheels with four holes, The N model grader had a solid cast 16" wheel with little offset, then from the E 27N on all our Fordsons had 16" front wheels with more offset to clear the later type king pins/ stub axles...
- Mon Apr 23, 2012 7:36 am
- Forum: Ford and Fordson Conversions
- Topic: 590E engine date and Thames Trader compliance
- Replies: 7
- Views: 14220
Re: 590E engine date and Thames Trader compliance
Mike, I also have what I think is a 590E engine in a Super Major. I bought it with the engine in already, but most of the rest of the tractor simply wasn't there. I was told by the fitter who I bought it off, and who half did the conversion, the engine he took out of a Clayson combine. Since it see...
- Mon Apr 23, 2012 5:59 am
- Forum: Fordson New Major
- Topic: Fitting a rear fork lift to a new major
- Replies: 5
- Views: 6161
Re: Fitting a rear fork lift to a new major
Hello Mike here again, I have now fitted the commercially manufactured rear fork now, it is quite a few years old and uses the single acting main lift ram, the shaft of this is quite large compared with my home made one. I have it all working but a few leaks to fix, ( rust preventative ) I haven't t...
- Mon Apr 23, 2012 5:12 am
- Forum: Fordson New Major
- Topic: 19" cast wheels, what difference between three and four hole
- Replies: 7
- Views: 8004
Re: 19" cast wheels, what difference between three and four
Hello, Each country generally hadtheir own wheels to help with the local content laws, you would likely get more reponse if you posted some pictures. Even wheels withinn Australia vary considerably with West Australian wheels not used in the East Coast and East Coast wheels not used in the West, so ...