injector pump coupler clatter

This forum is for the Fordson New Major, including the Super Major and the Power Major.
Post Reply
woodcutter
True Blue
Posts: 198
Joined: Tue Oct 18, 2011 10:34 pm
Location: hereford

injector pump coupler clatter

Post by woodcutter »

Hi all using the major today and noticed the coupler was louder than normal, and at idle engine seemed a bit uneven. so I wrapped a jubilee clip around coupler and all went quiet and ticking over a lot better :) Is there any reason I can't leave this as a permanent fix or should I do a proper job of fixing it. is it a hard job to change :?: it's a minimec pump any info would be appreciated.

Nick
True Blue
Posts: 712
Joined: Thu Jun 03, 2010 8:52 am
Location: Somerset UK

Re: injector pump coupler clatter

Post by Nick »

Hi, mine was quite clattery, so I changed it over, although it was on a vacuum governed pump. Its very simple, I disconnected all the pipes to the pump and unbolted it, slid the old coupler out, slid the new one in and put the pump back on in exactly the same position.

I would think after doing it , its probably a good idea to check the timing is right also :D
Oh yay, look, another seized bolt! Lets get a hammer.....and some kano.....and some cider!

BearCreek Majors
True Blue
Posts: 793
Joined: Tue Jul 21, 2009 3:16 am
Location: Wisconsin USA

Re: injector pump coupler clatter

Post by BearCreek Majors »

When I was a kid my dad wedged popsicle sticks in the coupler and then wrapped it up with electrical tape, It actually ran that way for several years. there is a vendor or two that sell the urethane pads, I have used several of theses and like them, they are quiet and reasonably priced, but the trade off is you loose the trademark rattle of the pump, its kind of like a Harley with quiet exhaust....something just doesn't quite sound rite.

Pat

anthonygos
True Blue
Posts: 79
Joined: Tue Nov 16, 2010 8:34 pm
Location: Now in South Wales/Born in Essex

Re: injector pump coupler clatter

Post by anthonygos »

Its the sound of a Major, just change it with a better coupler its not a hard job to do, go by post 2.
Don't just leave it in the shed, Fordson's are made to work, so take it out and work it....!

woodcutter
True Blue
Posts: 198
Joined: Tue Oct 18, 2011 10:34 pm
Location: hereford

Re: injector pump coupler clatter

Post by woodcutter »

I finally got around to changing the pad got an agriline one, jubilee clip looked a bit bodge :D when I took it apart I noticed the bolts that allow adjustment were too long and we're pressing against pump so I think that's why the pad seemed so noisey , so shortened bolts new pad and changed oil in pump and it's quieter than it's ever been happy days :D

Stu_Fletch
True Blue
Posts: 78
Joined: Thu Jun 05, 2014 10:45 am

Re: injector pump coupler clatter

Post by Stu_Fletch »

well done is it silent or can you still here it ever so slightly?

Cheers Fletch
Stuart Fletcher aka Fletch - 27 - Leicestershire in the UK

1955 Diesel Major - Ford 2701E engine
Ford 4100 Bubble Cab
1996 New Holland 7740 SLDP 4wd & loader

woodcutter
True Blue
Posts: 198
Joined: Tue Oct 18, 2011 10:34 pm
Location: hereford

Re: injector pump coupler clatter

Post by woodcutter »

Silent, I've just bought a new performance major and that's sounds noisey compared to this so I may have to change that one as well. I no people say the major should have the clatter but I like the quiet :)

Post Reply